How To Set Up Lexus Garage Door Opener

Press and concur buttons i and 3 for 15 seconds on HomeLink. Homelink buttons are on the rearview mirror or just above it.

Side by side, printing and hold button 1 on the HomeLink and at the same time press the button on your handheld garage door opener. Go on both pressed for well-nigh 8 seconds. The HomeLink LED light should start flashing rapidly.

2010-Lexus-ES-350 homelink buttons

Once you see the flashing light get to your garage door motor, you lot volition find the garage door motor mounted on the ceiling of your garage. Locate the Learn button on the back of the garage door motor and printing it one time. Practice non go along information technology pressed.

Rapidly go dorsum to the motorcar and printing button one on HomeLink a few times until the garage door starts to operate. The terminal stride can not accept more 30 seconds. Each press needs to be ii seconds long.

For more assist, follow the detailed step-by-step procedure below.

What you will need

Garage door remote
- Must have a working handheld remote.
Access to your garage.
Small ladder or step stool

Procedure

Locate the ane and 3 buttons on the rearview mirror
Press both buttons (1 and 3) simultaneously and concur down for a while until the LED lite begins to blink. This means that retentivity is cleared.
Ensure minimum proximity between your garage remote and the Homelink buttons.
Pick upward the handheld garage remote. Press andagree down the garage button while you press button "1" on Homelink. Hold for a while until the orange low-cal appears and starts blinking green—well-nigh 8 seconds.
Get to the garage and remove the casing on the motor to reveal the larn button. Press and release the larn push. Do not hold the larn button down too long, or you will erase all programmed remotes.
Become back to the car quickly and finish the connection by pressing the 1 push button on the rearview mirror a few times. Press the ane button anytime afterward that to unlock the garage door.

If y'all are non able to plan your Lexus garage door opener, repeat all of the steps. Steps five and 6 should be completed within thirty seconds. In footstep half-dozen, keep button 1 on HomeLink pressed instead of pressing the push several times.

How to program Lexus garage door opener without a remote?

You must have a remote that is programmed to open up your garage door. Y'all can not program a Lexus garage door opener without a preprogrammed handheld garage door opener. First, you lot program your handheld garage door. Next, plan your home link using the instruction on this page.

Every bit an alternative, you tin utilise the garage keypad if it is wireless, non hard-wired to the garage motor. You may have to remove the keypad or have the vehicle very close to it when yous complete step four.

Notes

When using your Lexus mirror button to open or shut the garage, you have to hold it downwards for about nigh ii seconds for it to work. One-touch does not work.
You only have 30 seconds to printing 1 of the buttons on the rearview mirror later on y'all press the Learn button on the back of the garage door motor. This step must do this step quickly.
Park vehicle right outside the garage. Close to the garage door but not nether the garage door.
Holding the 1st and 3rd Homelink buttons for 20-30 sec information technology would clear the retention.
The mirror LED will outset flashing or turn on solid. Flashing LED means you lot take a rolling code garage door opener. Solid green ways information technology's non a rolling code, and your buttons can now be programmed.

Programming stock-still lawmaking garage opener

The majority of garage door openers built before 1996 utilize stock-still code. This is how to program these units with your Lexus.

Hold the remote upwards to the HomeLink button you want to programme.
Push button both one of the HomeLink buttons and the remote button at the same time.
Hold them pressed until yous see the LED on the Lexus HomeLink brainstorm to flash rapidly.
Release both buttons. Your Lexus HomeLink button should exist programmed as a duplicate of the remote.

Yous must accept a working handheld garage remote.